ANATOMY OF A FLY LINE
When discussing fly line configurations, there are certain terms used. Fly lines embody two materials: the core and the coating. All of our fly lines have a core of braided nylon, braided monofilament or single strand of monofilament. Cortland Line Company is the only fly line company that manufactures its own fly line cores. The core is coated with a PVC in which we impart the taper design. Within the PVC we add hollow glass microspheres (floating) or various density compensating additives (sinking). Variations in the amount of additives used account for some of the differences in the characteristics of our lines, i.e. higher float or faster sink. READING OUR LABEL: The line designations are indicated on the front and bottom of Cortland’s packages as in this example: WF6S means weight-forward, 6-weight, sinking line. Another example: DT11F means double-taper, 11-weight, floating line. The length of the line is given (in this case 30 yards). The label also includes sink rate information. Example line is a Type 2, Fast. |
INSTALLING FLY LINE ON A REEL Install the backing first. Most fly fishers fill the spool of the reel with as much backing as possible to allow them to retrieve faster and to reduce line memory. Thereby the line is less likely to tangle. Read the reel capacity chart to determine the amount of backing needed for the reel. Find and loosen the end of the backing. Remove a few feet of line from the spool. Run the tag end through the front of the reel, around the spool, and out again. Tie a simple overhand slipknot in the tag end, then a single overhand knot, tighten and trim it. This tag end will be tied to the reel with an arbor knot. The backing should be installed by pulling it off a revolving spool. If the spool is laid flat on the ground and the backing coiled off (as when filling an open-faced spinning reel), it will twist and become tangled. Place a bunt pencil through the center of the spool of backing, so that the spool will rotate around the pencil. Place pencil between your knees. With the end of the backing tied to the reel, reel the backing onto the reel from the backing spool preferably through your fingers to apply tension while loading the line and to load the backing evenly onto the reel. Stop when enough backing is on the reel. Spooling fly line: Open the coil pack holding the fly line by twisting and carefully remove the fly line from the coil pack. Remove twist-ties from the line and replace it on coil pack. DO NOT place the line on the floor, because it will cause the line to twist or become entangled. Put the coil pack back together, leaving approximately a foot of line outside the coil pack. Tie the tagged end of the fly line to the backing using an Albright knot. Insert a blunt pencil through the hole in the center of the coil pack, so that the pack will freely rotate around the pencil. Place pencil between your knees and spool line slowly onto your reel. Guide line trough your fingers to apply tension and to load the line evenly onto the reel. The fly line should be fully loaded except 4 or 5 feet. Attach the butt (thick end) of your leader to the end of your fly line using a nail knot. PROPER FLY LINE CARE At Cortland, we build our fly lines to provide you with many hours of trouble free use, but it is your responsibility to extend the life of the fly line, and maintain proper performance through routine care. Avoid excessive heat exposure to the lines by keeping your reels out of direct sunlight. Avoid car dashboards or rear window ledges when transporting. Clean and dry fly line and backing before storing. Also, use Cortland XL Cleaner before and after each outing to ensure maximum performance and longer lasting lines. Sharp objects such as roughened reel surfaces and worn fly rod guides will quickly destroy your fly line. Replace defective reels and rod guides as soon as possible. DO NOT expose lines to petroleum based products or insect repellents. Many of the chemicals found in a variety of outdoor related products are very harmful to your line finish. WEIGHT CONFIGURATIONS Fish take a majority of their food below the surface. Full sinking and sink tip lines are often the only way to get the fly to where the fish are feeding. Eventually all sinking lines reach the same depth. However, the speed in which the line reaches the various depths is often the deciding factor in whether or not fish are being caught. The following chart gives the sink rate for each type of sinking line. variations within each rate are due to the different line sizes themselves. I.e. a 10 weight type 6 is a bit faster than a 6 weight type 6.
FLY LINE CODES
|
